Drift firmware update archive 66MB
by
zemerdon »
Sat Aug 24, 2024 9:28 am
Acuvance update software
Futaba CIU2-CIU3 driver
Futaba R334SBS firmware
Futaba R404SBS firmware
Futaba SBD-1 Link firmware
Futaba S-BUS PC Link...
0 Replies
293 Views
Last post by zemerdon
Sat Aug 24, 2024 9:28 am
WIRE/AWG Chart
by
zemerdon »
Mon Jul 22, 2024 9:30 am
(AWG) Strand Strand diameter(mm/mil) Area(mm²) Insulation(mm) OD(mm) Length spool(m/ft)
20 26 0.160 / 6.30 0.52 0.38 / 15 1.8 / 0.071 12 / 40
21...
0 Replies
1469 Views
Last post by zemerdon
Mon Jul 22, 2024 9:30 am
ESC cooling mod COMPLETE
by
zemerdon »
Thu Jun 13, 2024 5:23 pm
proposed plan...
20240608_110045.jpg
copper heatsink 35x35x7mm 41g
XARVIS XX temps
all tests were held at throttle for approx. 120s.
No fan...
0 Replies
2199 Views
Last post by zemerdon
Thu Jun 13, 2024 5:23 pm
ESC settings explained
by
zemerdon »
Thu Jun 13, 2024 4:16 pm
Drive frequency
In addition to the conventional 1-16kHz (1kHz step) and 18-32kHz (2kHz step), 35, 38, 42, 48, 55, and 64kHz have been added.
⇒ By...
0 Replies
1952 Views
Last post by zemerdon
Thu Jun 13, 2024 4:16 pm
Gyro settings explained
by
zemerdon »
Sat Jun 01, 2024 9:57 am
Responde Mode
Gyro sensor response setting.
Low -> Middle -> High speed up response.
In high mode, using the dead band angle is too small, the...
0 Replies
2010 Views
Last post by zemerdon
Sat Jun 01, 2024 9:57 am
HPS-CD700 + GYD550 settings
by
zemerdon »
Sat Jun 01, 2024 1:54 am
Working HPS-CD700 + GYD550 settings for my RDX Kansei V2.
cd700_config1.jpg
cd700_config2.jpg
gyd550_config1.jpg
gyd550_config2.jpg...
0 Replies
2301 Views
Last post by zemerdon
Sat Jun 01, 2024 1:54 am
Servo settings explained
by
zemerdon »
Wed May 29, 2024 6:02 pm
Dead band
The dead band angle at stopping can be specified.
Small - Dead band angle is small and a small signal change immediately operates the...
0 Replies
1950 Views
Last post by zemerdon
Wed May 29, 2024 6:02 pm
Thorttle cut 10PX
by
zemerdon »
Mon May 06, 2024 12:39 pm
I've bound Program Mixing 1 to a push button, SW3. The values change live, so if you pull the trigger slightly to throttle and change settings you...
0 Replies
1989 Views
Last post by zemerdon
Mon May 06, 2024 12:39 pm
0 Replies
1567 Views
Last post by zemerdon
Sat May 04, 2024 1:27 pm
Futaba SBUS
by
zemerdon »
Thu Apr 11, 2024 5:26 pm
SBus
Depending on the servo, it could be either HV or not. Look in the description for the HV designation.
SBus servos need to be programmed to a...
0 Replies
1304 Views
Last post by zemerdon
Thu Apr 11, 2024 5:26 pm
Body wishlist
by
zemerdon »
Sun Apr 07, 2024 10:52 am
Jaguar Vision Gran Turismo SV 3D Printing body
JAGUAR XJ6 SEDAN PRINTABLE BODY CAR
0 Replies
1210 Views
Last post by zemerdon
Sun Apr 07, 2024 10:52 am
Cameras etc
by
zemerdon »
Sun Apr 07, 2024 10:51 am
fujifilm X-T4
Olympus PEN F
Gopro 8, DJI Mavic pro
0 Replies
1235 Views
Last post by zemerdon
Sun Apr 07, 2024 10:51 am
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum